The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?()A.network 172.26.168.0 area 478B.network 172.26.0.0C.network 172.26.168.128 0.0.0.127D.network 172.2

题目内容(请给出正确答案)

The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?()

A.network 172.26.168.0 area 478

B.network 172.26.0.0

C.network 172.26.168.128 0.0.0.127

D.network 172.26.168.128 area 478

参考答案和解析

参考答案：B

如果没有搜索结果或未解决您的问题，请直接联系老师获取答案。

更多相关问题

第1题

Refer to the exhibit. BigBids Incorporated is a worldwide auction provider. The network uses EIGRP as its routing protocol throughout the corporation. The network administrator does not understand the convergence of EIGRP. Using the output of the show ip eigrp topology all - links command, answer the administrator‘s questions.Which three networks is the router at 172.17.10.2 directly connected to?（）A. 172.17.0.0/30B. 172.17.1.0/24C. 172.17.2.0/24D. 172.17.3 .0/25E. 172.17.3.128/25F. 172.17.10.0/24

点击查看答案
第2题

Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?（）A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

点击查看答案
第3题

According to the following output, can you tell me which command can redistribute IGRP into EIGRP?()A. Under t he router eigrp mode add redistribute igrp 123 subnetsB. Under the router igrp mode add redistribute eigrp 123C. None, EIGRP and IGRP are automatically redistributed in this instance.D. Under the router eigrp mode add redistribute igrp 123

点击查看答案
第4题

Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）A. Redistribute connected interfaces on router B and router CB. Set the maximum nu mber of equal cost paths to1 in all routersC. When redistributing EIGRP into OSPF, set the external metric type to type E1D. Adjust the default metrics in router B and router C so that the values are different in each routerE. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol

点击查看答案
第5题

Refer to the exhibit. Router B is performing bidirectional redistribution between EIGRP an d OSPF.The network 10.100.1.0/24 should not be reachable from the 10.100.9.0/24 network. However, it needs to be reachable from any network within the EIGRP domain. All other networks should be seen in both domains. Which change to router B would accom plish these goals?（）A. Under the EIGRP process, insert the distribute - list block_net_1 out ospf 1 command.B. Under the OSPF process, insert the distribute - list block_net_1 in serial1/0 command.C. Under the EIGRP process, insert the distribute - list block_net_1 in serial1/0 command.D. Under the OSPF process, insert the distribute - list block_net_1 out eigrp 1 command.

点击查看答案
第6题

After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What information can you determine about this network?()A. The network is stableB. There is a flapping link or interface, and router C knows an alternate path to the networkC. There is a flapping link or interf ace, and router C does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination

点击查看答案
第7题

After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What can you conclude about this network? ()A. The network has been stable for at least the last 45 minutesB. There is a flapping link or interf ace, and router C knows an alternate path to the networkC. There is a flapping link or interface, and router A does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination

点击查看答案

The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?()

题目内容(请给出正确答案)

参考答案和解析

更多相关问题

第1题

第2题

第3题

第4题

第5题

第6题

第7题

相关内容