Refer to the exhibit.The actual speed of the serial links between R2 and R3 are 256 kb/s and 512k b/s respectively. When configuring EIGRP on routers R2 and R3, the network administrator configured the bandwidth of both serial interfaces to 512 kb/s. What

题目内容(请给出正确答案)

Refer to the exhibit.The actual speed of the serial links between R2 and R3 are 256 kb/s and 512k b/s respectively. When configuring EIGRP on routers R2 and R3, the network administrator configured the bandwidth of both serial interfaces to 512 kb/s. What will be the effect?（）

A. EIGRP will overutilize the 512 kb/s link.

B. The interface "delay" value used in the EIGRP metric calculation will be inaccurate on the 256k b/s serial interface.

C. The amount of bandwidth used for EIGRP routing protocol traffic on the 256 kb/s link can become excessive.

D. EIGRP can load balance between the two serial links only if the variance is set to 2 or higher.

E. Unequal cost load balancing will be disabled.

如果没有搜索结果或未解决您的问题，请直接联系老师获取答案。

更多相关问题

第1题

已知R2＝1000,R3＝200,执行指令MOV R2,R3, LSL2后，R2＝___【15】____,R3=__【16】_____。

点击查看答案
第2题

Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0

点击查看答案
第3题

Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?（）A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

点击查看答案
第4题

Refer to the exhibit. On the basis of the configuration provided, how are the Hello packets sent by R2 handled by R5 in OSPF area 5?()A. The Hello packets will be exchanged and adjacency will be established between routers R2 and R5.B. The Hello packets will be exchanged but the routers R2 and R5 will become neighbors only.C. The Hello packets will be dropped and no adjacency will be established between routers R2 and R5.D. The Hello packets will be dropped but the routers R 2 and R5 will become neighbors.

点击查看答案
第5题

Refer to the e xhibit. It is desired to set up a BGP neighbor relationship between routers R1 and R4. BGP packets between them could travel through R2 or R3. What is the simplest configuration that will allow for failover?（）A. Configure BGP n eighbor relationships between all interfaces on R1 and R4.B. Install a direct connection between R1 and R4.C. Configure loopback interfaces on R1 and R4 to provide the update source address for BGP packets.D. Configure only one neighbor relationship between R1‘s 192.168.1.2 interface and R4‘s 172.16.10.2 interface.

点击查看答案
第6题

Refer to the exhibit. Autonomous systems 200 and 300 have EBGP sessions established with their directly connected routers in au tonomous system 100. IGP has been configured on all routers in autonomous system 100 and they successfully exchange routing updates. Traffic originated in autonomous system 200 cannot reach the destination autonomous system 300. What configuration shoul d be done on the routers in autonomous system 100 in order for the traffic coming from autonomous system 200 to be forwarded to autonomous system 300?（）A. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned off.B. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned on.C. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned on.D. IBGP session mu st be established between routers R1 and R3, and the synchronization must be turned off.E. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned off.F. IBGP session must be established between routers R1 and R3, and the synchronization must be turned on.

点击查看答案
第7题

Refer to the exhibit. On the basis of the configuration that is provided, how would the BGP updates that come from router R1 be replicated inside autonomous system 65200?()A. All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5B. None of the BGP updates that are received on router R2 will ever be received by router R5C. All BGP updates that are received on router R2 will not be sent to routers R3 and R4D. All BGP updates that are received on router R2 will be sent directly to router R5

点击查看答案

Refer to the exhibit.The actual speed of the serial links between R2 and R3 are 256 kb／s a

题目内容(请给出正确答案)

更多相关问题

第1题

第2题

第3题

第4题

第5题

第6题

第7题

相关内容