To allow HTTP access to the WLAN controller
To allow SSH access to the CLI of the WLAN controller
To allow SSL access to the CLI of the WLAN controller
To allow HTTPS access to the WLAN controller
None of the other alternatives apply
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
点击查看答案
You have just configured a static default route on router TK1. What is the purpose of a default route?()A. It is a route to be used when the routing protocol fails.B. It is a route configured by an ISP that sends traffic into a corporate network.C. It is a route used when a packet is destined for a remote network that is not listed in the routing table.D. It is a route manually configured for a specific remote network for which a routing protocol is not configured.E. It is used to send traffic to a stub network.
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:TK1(config) router ospf 1TK1(config-router) network 10.10.10.0 255.255.255.0 area 0After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）A. The AS is not correctly configuredB. The network subnet mask is incorrectly configuredC. The network wildcard mask is configured incorrectlyD. The network number is not correctly configuredE. The process id is configured incorrectlyF. None of the above
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）A、The AS is not correctly configuredB、The network subnet mask is incorrectly configuredC、The network wildcard mask is configured incorrectlyD、The network number is not correctly configuredE、The process id is configured incorrectlyF、None of the above
You have configured the "config network webmode enable" command on a Cisco device. What is the purpose of this command？ （）A、To allow HTTP access to the WLAN controllerB、To allow SSH access to the CLI of the WLAN controllerC、To allow SSL access to the CLI of the WLAN controllerD、To allow HTTPS access to the WLAN controllerE、None of the other alternatives apply
You have a domain controller that runs Windows Server 2008 and is configured as a DNS server. You need to record all inbound DNS queries to the server. What should you configure in the DNS Manager console（）A、Enable debug logging.B、Enable automatic testing for simple queries.C、Enable automatic testing for recursive queries.D、Configure event logging to log errors and warnings.
You are an administrator of a small business network. You have one dial-up account at an ISP and want all computers on your network connect to the Internet. You have enabled Internet connection sharing. You do not want to initiate this connection automatically when a request for Internet reaches your computer. What should you do? （）A、You should uncheck “Enable on demand dialingB、Enable on-demand dialingC、Enable sharing a modem on one computer on the networkD、Configure a DHCP ServerE、Disable Internet Connection Sharing
